CPCCLRG3002 Licence to perform rigging intermediate level

This unit specifies the skills and knowledge required to safely perform intermediate rigging work.

Riggers use mechanical load shifting equipment and associated gear to move, place or secure loads, including plant, equipment or members of a building or structure. Riggers ensure the stability of those members and set up and dismantle cranes and hoists.

This unit includes rigging work involving:

hoists with jibs and self-climbing hoists
cranes, conveyors, dredges and excavators
tilt slabs
demolition of structures or plant
multiple lifts.

Rigging work is undertaken in construction and other industries where load shifting equipment is used to move, place or secure loads.

Completion of the general construction induction training program, specified in the Safe Work Australia model Code of Practice: Construction Work, is required by anyone carrying out construction work. Achievement of CPCCWHS1001 Prepare to work safely in the construction industry meets this requirement.

This unit has a pre-requisite requirement. This requirement may be met by either the successful completion of the unit CPCCLRG3001 Licence to perform rigging basic level or holding a valid licence for dogging.

Intermediate Rigging Course – CPCCLRG3002
Takes a step up from basic rigging course with more advanced safety apparatus;
To demonstrate competency in this unit, a candidate must meet the elements and performance criteria by safely performing rigging tasks at an intermediate level, including:

undertaking a multiple-crane lift of a load of at least 1 tonne and at least 4 m long
erect and dismantle one of the following:
- a tower crane section
- crane lattice boom section
- a fly jib on a mobile slewing
- a non-guyed tower crane.
installing and removing a three-panel structure, with each panel being at least 4 m high, at least 2 m wide and at least 1.5 tonnes
using the following bends and hitches:
- round turn
- two half-hitches.

The candidate must:

check relevant workplace information, including safe work method statements (SWMSs) and equipment service and maintenance records and checklists
perform all activities in compliance with workplace-specific, safe work and manufacturer requirements
identify hazards and use appropriate risk controls and safety measures and equipment
use the following associated gear:
- tag lines
- flexible steel wire rope (FSWR)
- chains
- wire and synthetic slings
- shackles
- wedge sockets
- eye bolts
- rope grips
- turnbuckles
- chain blocks
- sheaves
- spreader bars or lifting beams
- snatch blocks
- lifting clutches
safely erect and dismantle structures and plant.

CPCCLRG3002 – Licence to perform rigging intermediate level; 4 days including SafeWork NSW assessment
$1,700.00

Must have current dogging licence
All students must pass a language, literacy & numeracy assessment (LLN)
Minimum 18 years of age (Workplace Health and Safety requirement)
PPE is required including safety boots and a hi-vis shirt
Identification must be the originals and not laminated,
100 points Safework NSW EOI – SW08446-0718-423971.pdf

Three (3) assessments will be conducted over the duration of the course – (formative assessment) Knowledge, Calculations and Practical Assessments.
On the last day of the course a summative assessment will be conducted by an approved State regulatory body assessor (e.g. Safe Work NSW) All critical components must be demonstrated and answered correctly.

Applicants deemed not yet competent will be provided the opportunity to undergo further training.
Applicants cannot be reassessed for a minimum of 48 hours from the date of the original assessment.

Note: there may be an extra cost for re-assessment

These are Nationally Recognised Training courses and applicants deemed competent at the conclusion of the course will be provided with a Statement of Attainment CPCCLRG3002 – LICENCE TO PERFORM RIGGING INTERMEDIATE LEVEL

In the event of cancellation or withdrawal:

Students who give notice to cancel their enrolment more than 10 days prior to the commencement of a program will be entitled to a full refund of fees paid.
Students who give notice to cancel their enrolment less than 10 days prior to the commencement of a program will be entitled to a 75% refund of fees paid. The amount retained (25%) by All Onsite Training and Assessment Services is required to cover the costs of administration and resources which will have already been committed based on the students initial intention to undertake the training.
Students who cancel their enrolment within 1 full business day prior program commencement OR after a training program has commenced will not be entitled to a refund of fees.
If All Onsite Training and Assessment Services cancels the training course, and is not rescheduling then a full refund will be returned to the payer

Apply for a new licence or class

You will need to go to a participating Australia Post in person to apply. You need to do this within 60 days of receiving your Notice of Satisfactory Assessment from your SafeWork NSW assessor.

You will need to take:

your Notice of Satisfactory Assessment form
a completed Application for a National Licence to Perform High Risk Work – New Application form (N5 form provided by your SafeWork NSW assessor). Do not sign this form, you need to sign it at Australia Post
passport-quality photograph
proof of identity. See evidence of identity information sheet (PDF, 109.92 KB)
any current high risk work licences
payment method (view the cost in the fee schedule).

Training/assessment can be conducted at AOTA Training Facility – 275a Princess Highway, Unanderra NSW

PPE is required including safety boots and a hi-vis shirt
100 points of ID – (including photo ID) link to Safework NSW EOI: SW08446-0718-423971.pdf
Unique Student Identifier Number – http://www.usi.gov.au/create-your-USI/Pages/default.aspx – if you need help with this our trainer will help you on the day.